Hildebrand Machinery Co Inc
2023 Black Bridge Rd
York
PA
17402-1934
Tel: 717-846-2600
Fax: 717-845-9497
sales@hildebrandmachinery.com www.hildebrandmachinery.com
150 Ton, PH, Mod 4C150T, 20" Str of Clamp & Punch & Cushion, 4 Post, 33" x 66" Bed, New '96
[06143]
Stock # 06143-P
150 TON PH HYDRAULICS & AUTOMATION HYDRAULIC PRESS
Serial # 60556 New 1996 Model # 4C150T
FRAME SPECIFICATIONS:
Capacity at 2550 PSI: 150 Tons
Stroke of Clamp Platen (Adjustable): 20"
Stroke of Punch Ram (Adjustable): 20"
Stroke of Cushion: 10"
Table to Platen, Platen Up (Open Height): 42"
Between Columns: 66" L-R x 33" F-B
Table, Front to Back, Overall: 48"
Table to Floor: 39-3/4"
Cylinder Size:
Punch (1) 10" Bore x 7" Diameter Area: 100 Tons
Clamp (2) 6" Bore x 4" Diameter Ram: 50 Tons
Cushion (1) 8" Bore x 5-1/2" Diameter Ram: 50 Tons
A single point air operated "safety latch" will be interlocked with the controls to prevent the clam
platen from lowering unless the operator's dual punch button controls are activated.
MOVING PLATEN AND GUIDE RODS:
The platen and guides are of welded steel construction with full continuous welding. The column hou
ings are inline precision bored for the press tie rods and designed with split bushings f
r ease of maintenance.
Bearing housings furnished with wiper rings held in place by retaining rings. This design maintains
grease in the guides and prevents entry of foreign material which may cause unnecessary w
ar on the bushings and columns.
The bearing housings are of long design to insure accurate guiding through the press stroke. Guide
ousings to be drilled for grease fittings.
All weldments are stress relieved after welding and before machining.
HYDRAULIC EQUIPMENT:
For use with water Glycol fluid. Flash point of standard hydraulic fluid is 400 deg. F.
Pumps:
Punch - 80 & 21 GPM constant delivery double type at 1800 RPM
Clamp - 55 & 15 GPM constant delivery double type at 1800 RPM
Cushion - 32 GPM constant delivery type at 1800 RPM
The top mounted reservoir is a welded tank with pump, motor and valve system conveniently located fo
ease of maintenance. The reservoir is sandblasted and cleaned to remove scale and dirt
hich may contaminate the hydraulic system. Approximately 500 gallon capacity.
The reservoir has large clean out covers for ease of maintenance.
Water cooled heat exchanger with temperature control, circulating water only on demand.
Three panel mounted tonnage gauges with pressure adjusting knobs for clamp platen, punch and cushion
Pressure adjustable 20% to 100% of maximum capacity.
EQUIPPED WITH:
Magnetic suction strainer
Return line filter with mechanical indicator
Manifold mounted valves with indicator lights
CONTROL:
TRIPLE ACTION MODE:
Press dual push buttons simultaneously (no tie down), clamp platen and punch advance. Release dual
uttons, clamp platen and punch return. Hold dual buttons, clamp platen and punch advance
to a programmable position and shift from "advance" to "press" speed at the same time beginning a se
uence of operation.
Return stroke is adjustable and electric "jogging" is included for set-up, with dual buttons to retu
n the clamp platen and punch. All press and motor control buttons are at the operator's
osition. The "press" advance and motor start buttons have protective enclosures. The "emergency" s
op button is an open, mushroom type.
Note: In the triple action mode the punch will not travel beyond the clamp platen during dwell.
SINGLE ACTION MODE:
Press dual push buttons simultaneously (no tie down), clamp platen and punch combined advance. Rele
se dual buttons, clamp platen and punch combined return. Hold dual buttons, clamp platen
and punch combined advance to a programmable position and shift from "advance" to "press" speed. Wh
n a programmable down stroke position is reached the clamp platen and punch combined reve
ses automatically (distance reverse) or on contacting the work, builds up to a pre-set pressure and
everses automatically (pressure reverse). Dual buttons must be released to start a new c
cle (non-repeat).
Return stroke is adjustable and electric "jogging" is included for set up with dual buttons to retur
the platen. All press and motor control buttons are at the operator's position. The "e
ergency" stop button is an open, mushroom type.
APPROXIMATE AVERAGE SPEEDS:
Advance: 500 IPM
Press (Adjustable): 25-55 IPM
Return (Clamp & Punch): 570 IPM
(Cushion): 150 IPM
MOTOR:
(1) 50 HP, T.E.F.C., 1800 RPM, wired for 480 Volt, 3 Phase, 60 Hertz for punch
(1) 25 HP, T.E.F.C., 1800 RPM for clamp platen
(1) 10 HP, T.E.F.C., 1800 RPM for cushion, filtering, cooling and pilot pressure
MOTOR CONTROLS:
Control cabinet NEMA-12 dust proof and oil-tight
Magnetic starter fused disconnect
110-volt transformer
Allen Bradley electrical components
Positional control of the clamp platen and punch will be selected through individual key pads on the
operator's panel. Temposonic position transducers in the punch and clamp cylinders provi
e the appropriate communications through a Dyatronics Panel Meter (key pad) to achieve this control
ith accuracy of set points and repeatability.
All limit switches are eliminated in the press circuitry except for (2) on the cushion - down and up
stroke limits.
EQUIPPED WITH:
Low pressure pre-load in the cushion
Three Brad Harrison safety plus for guarding
Set of (8) cushion pins
Two removable 2" die locating pins and mounting blocks
Four additional 1" tapped holes in the bed per Faith Tool pattern
Set of safety jacks
Safety circuit in jog
Stroke adjustment control which includes Daytronics unity and programming
Vicker's hydraulic components
Two roller type hydraulic die lifters mounted in parallel slots front to back in press
bed, maximum die set weight 10,000 lbs.
Two removable type die change rails mounted on front of press
OPERATING VOLTAGE:
480 Volts/3 Phase/60 Cycle
Note: This press is currently equipped with a special mold set used in its last operation. This mo
d has features that are integrated into the press controls. The press can be used for ot
er conventional applications but may require some changes to be capable of the user's process.
This press requires a pit for the cushion.
SHIPPING DIMENSIONS:
Press: 93" L-R x 70" F-B x 162" H x 48000 lbs.
Press Control: 48" L-R x 24" F-B x 60" H
Mold Control: 48" L-R x 24" F-B x 60" H
Hydraulic Chiller: 40" L-R x 30" F-B x 30" H
Box of Parts: 96" L-R x 48" F-B x 31" H
Press Control Cabinet: 84" L-R x 40" F-B x 30" H
Loaded on Truck, Our Warehouse, York, PA
For information on a specific piece of equipment, please contact the selling dealer directly.
UED-ed is published by
Used Equipment Directory
400 Morris Ave Ste 268, Denville NJ 07834
Robert Scofield, Publisher. Email: bobs@buyused.com,
Tel: 973-400-1790 Fax: 973-625-8933
|
