Presses For Industry Inc
20501 Hoover Rd
Detroit
MI
48205-1075
Tel: 313-839-9300
Fax: 313-839-9600
chip@pfisales.com www.pressesforindustry.com
1000 Ton, DANLY S4-1000-180-84, 33"STR, 91"SH, 180"X84"BA, 57"WIN, RECONDITIONED
[4137]
PRELIMINARY SPECIFICATIONS
MODEL S4-1000-180-84
4 POINT PRESS STRAIGHT SIDE DOUBLE CRANK
SINGLE ACTION
1000 TON CAPACITY
33" STROKE
91" SHUT HEIGHT
11.5" ADJUSTMENT
180" X 84" BED AREA
10 SPM
28.5" FLOOR TO TOP OF BOLSTER
EQUIPPED WITH:
150 HP MAIN MOTOR
MOTOR & CONTROLS
AIR CLUTCH & BRAKE
AIR COUNTER BALANCE
FRONT TO BACK ROLLING BOLSTER
(2) 57"W X 29"H WINDOWS
TONNAGE MONITOR
STROKE INDICATOR
SIEMENS SIMATIC TOUCH CONTROL
ALL NEW ELECTRICS IN 2006
DUAL PALM CONTROLS
12" T-SLOTTED BOLSTER
T-SLOTTED RAM
4-POINT GIBBING
SET-UP FOR CUSHIONS
- CUSHIONS AVAILABLE THROUGH 3RD PARTIES
ELECTRICAL REQUIREMENTS:
575 VOLT
APPROX O.A. WEIGHT: 658,000LBS
APPROX O.A. DIMENSIONS: 324"LR X 240"FB X 37'H
- 27'10"H ABOVE FLOOR
- 9'9" BELOW FLOOR
APPROX O.A. PIT DIMENSIONS: 324"LR X 198"FB X 118"D
IN CANADIAN PLANT UNDER POWER
Work Performed from September 2005 to March 2006
Please Note this work was in Addition to all Standard work
Performed when Relocating a Press and Providing a Full Start-up!
Press in General
Updating of all Electrical (Complete Re-wire), Pneumatics and
Hydraulics to Meet CSA, TSSA & Z-142
Complete Rebuild of Ram
Complete Rebuild of Crown
Crown:
Visual Inspection of gear tooth wear and antifriction bearing
conditions
Full Inspection of Clutch & Brake
Compete Teardown and Inspection of Flywheel All repairs Made
Checked Conditions & Repair of all Gears, Linkages, Bore
Information and Keyways
Check & Repair of Eccentric Lobes and Connecting Arm Bushings
Check Lower Connections, Wrist Pins, Bushing
Cleaning of Crown Interior
All Components out of Tolerance or in Excess of Acceptable Wear,
were Replaced, Repaired or Modified to Achieve Industry Standards
The Press Ram
Note: All Ram Re-work was Performed by Danly Press
All Components Cleaned and Inspected
All Components were checked with Die Penetrate for Cracks
All Parts were Inspected to meet Original Danly Specs. Any that
did not were Replaced
All Shafts and Screws were put on a lathe and Checked for
Straightness and Concentricity
Lift Check on Ram Adjust Threads
Complete Rebuild of Hydraulic Overloads with replacing of all
seals and Rings
Purchased, Machined, T-Slotted, Drilled and Tapped and Installed
Counter Balances
Work Performed by Danly Press
All (3) Counterbalances were Completely Disassembled and
Inspected by Danly
The ID was Machine Honed to remove any scoring and the OD of the
Piston Center was turned on the Lathe
All Packing, Fiber Wear Rings and Seals were Replaced
Spot Chromed where Necessary
Air Tanks
All (3) Air Receptacles were Thickness Checked, Crack Checked,
Rust Wear Checked and Approved by TSSA
New Victaulic Piping was Piped to Counterbalances
Rolling Bolster
All Hydraulic Cylinders were inspected and Seals replaced
All Electrical was Replaced with New
Tie Rod & Nuts turned on the Lathe
The Tie Rods were Cleaned and Inspected for Damaged
The Hydraulic Tie Rod Nuts were Given New Seals
For information on a specific piece of equipment, please contact the selling dealer directly.
UED-ed is published by
Used Equipment Directory
400 Morris Ave Ste 268, Denville NJ 07834
Robert Scofield, Publisher. Email: bobs@buyused.com,
Tel: 973-400-1790 Fax: 973-625-8933
|
