Gibbs Machinery Co
21500 Hoover Rd
Warren
MI
48089-3160
Tel: 586-755-5353
Fax: 586-755-0304
sales@gibbsmachinery.com
www.gibbsmachinery.com
10" x 20", Landis No. 1R, 1967, Rebuilt 2000, #3787
[3787]
EQUIPPED WITH:
Coolant Plunge Feed Marposs Gaging
SPECIFICATION:
Nominal Work Swing ........................................... 10"
Nominal Distance Between Work Centers ........................ 20"
Maximum Diameter Work Standard Machine Will Grind With
Full Size Standard Wheel .................................. 10-7/8"
Minimum Diameter Wheel To Grind Zero Diameter Work On
Centers ................................................... 10-1/2"
Floor Space Required ......................................... 106" x 50"
Coolant Tank Capacity ........................................ 19 Gal.
Hydraulic Tank Capacity ...................................... 9-1/4 Gal.
Height From Floor To Work Centerline ......................... 41-3/4"
Work Carriage:
Traverse Speed ............................................ 2 - 240"/Min.
Carriage Traverse Per Turn Of Handwheel ................... 0.200"
Swivel Table Graduated (20 Degrees Including Angle) ....... 4"/Ft.
Work Rest Capacity ........................................ 1/4" - 4"
Wheelhead & Wheelfeed:
Grinding Wheel Size (Standard) ............................ 12" x 1" x 5"
Grinding Wheel (Maximum Width) ............................ 1-1/2"
Grinding Wheel Spindle Speeds (RPM) ....................... 2000 & 2530
Grinding Wheel (Minimum Diameter Of Worn Wheel) ........... 7-1/2"
Maximum Distance Wheel Ceterline To Work Centerline:
Machines With Handwheel ................................ 11-1/2"
Machines With Hydraulic Infeed ......................... 12-1/2"
Minimum Distance Wheel Centerline To Work Centerline
With Footstock Removed .............................. 3-1/2"
Work Diameter Reduction Per Revolution Of Handwheel .... .100"
Per Revolution Of Fine Feed Knob .................... 0.001"
Minimum Feed Graduations On Diameter ................... 0.000050"
Maximum Hydraulic Infeed On Diameter For Machines
With Hydraulic Infeed ............................... 0.090"
Rapid Infeed Stroke For Machines With Hydraulic Infeed . 1"
Grinding Wheelhead Swivel Range ........................ 90 Degrees Ea. Way
Internal Grinding Spindle Speeds (RPM) ................. 16,500
Headstock & Footstock:
Headstock Work Center .................................. #10 Jarno
Footstock Work Center .................................. #6 Jarno
Headstock Swivel Range ................................. 120 Degrees
Work Speeds (RPM) ...................................... 60, 90, 150, 225,
Diameter Hole Through Spindle .......................... 1"
Headstock Spindle Nose ................................. 5A2
Electric Motors:
Wheel Drive Motor ...................................... 3 HP
Work Drive Motor ....................................... 1/4 HP
Wheel Spindle Lubrication Motor ........................ 1/4 HP
Coolant Pump Motor ..................................... 1/10 HP
Hydraulic Pump Motor For Machines W/Hyd. Traverse
And/Or Hydraulic Infeed ............................. 1 HP
Internal Grinding Spindle Motor ........................ 1 HP
Weights:
Machine With Hand Traverse And Hand Wheelfeed .......... 4,000#
**NOTE** Machine Is In Good Condition! Machine has been rebuilt.
Machine was disassembled, the table ways & wheel slide ways have
been hand scraped. The Geometry is returned to new. The Table Top
swivel has been brought to new tolerance. The HeadStock has been
checked and brought to new tolerance. The TailStock has been
checked and rechromed and reground if necessary.
The Hydraulic System-pumps, liner and valves have been checked and
replaced or repaired as necessary.
The Electric System has been checked and all starter contactors-
transformers and wiring has been checked and are guaranteed to be
in good operating condition. Can arrange for 220-230 - 440-460 Volt
operation.
The Coolant System has been reconditioned.
This work was done while we were slow - I could not do all this work
today for this price.
UED-ed is published by
Used Equipment Directory
45 Eisenhower Dr 5th Fl, Paramus NJ 07652
Robert Scofield, Publisher. Email: bobs@buyused.com,
Tel: 201-845-2452 Fax: 201-845-2496
|
