STAR Assets
101 W 81st St Ste #221
New York
NY
10024-7220
Tel: 212-799-2943
Fax: 208-439-8859
mettinger@starassets.com
OKUMA LT-15MY, U100L, Twin Spindle-LiveTools & Y Axis, Options, Much Tooling, 2001
[0318102]
OKUMA LT15-MY TWIN-SPINDLE CNC TURNING CENTER
w/ LIVE TOOLS & Y AXIS
2001 MACHINE -VERY GOOD CONDITION
EQUIPPED WITH:
OSP - U100L CONTROL WITH CYCLE TIME REDUCTION,
ANIMATION, HELICAL CUTTING, & SYNCHRO TAPPING
AUTO MOON ROOF
REAR CHIP CONVEYOR
COORDINATE CONVERSION
C-X CONTOURING
CYCLE TIME REDUCTION
8" KITAGAWA 3-JAW CHUCK FOR SPINDLE 1
ROYAL CDC 60 QCD QUICK CHANGE COLLET CHUCK ON SPINDLE 2
PARTS CATCHER
BAR FEED INTERFACE
SMW “SPACESAVER 2100” BAR FEEDER
ROBOT INTERFACE TYPE D
SPINDLE ORIENTATION
11 LIVE TOOL HOLDERS (VDI40) - FACE WORKING IN REFERENCE TO LATHE CENTERLINE
2 LIVE TOOL HOLDERS (VDI40) - 3X SPEED INCREASERS - FACE WORKING IN REFERENCE
TO LATHE CENTERLINE
4 LIVE TOOL HOLDERS - CROSS WORKING IN REFERENCE TO LATHE CENTERLINE
SPECIFICATIONS:
NO. OF CONTROLLED AXES: 8
SWING OVER BED: 21.65"
SWING OVER CARRIAGE: 5.91"
DISTANCE BETWEEN CENTERS: 46.46" MAX
10.24" MIN
MAXIMUM TURNING DIAMETER X LENGTH: 8.27" X 7.87"
SPINDLE
SPINDLE DIAMETER: 3.94"
SPINDLE NOSE TYPE: JIS A2-6
THROUGH SPINDLE HOLE (NOT BAR CAPACITY): 2.44"
NO OF SPINDLE SPEED RANGES: 2 STEPS
SPINDLE SPEED: 75 TO 4500 MIN -1
CROSS SLIDE (X-AXIS)
AXIS TRAVEL: 9.65" UPPER
9.06 LOWER
FEEDRATE: 0.00001 TO 39.37 IPR
RAPID FEEDRATE: 787.40 IPM
CARRIAGE (Z-AXIS)
ZA-AXIS TRAVEL (UPPER TURRET): 18.11"
ZB-AXIS TRAVEL (LOWER TURRET): 35.43"
ZC-AXIS TRAVEL: 18.11"
FEEDRATE: 0.00001 to 39.37 IPM
RAPID FEEDRATE: 944.89 IPM
Y-AXIS (UPPER TURRET)
AXIS TRAVEL: 2.76" 1.97"
FEEDRATE: 118.11 IPM
RAPID FEEDRATE: 236.22 IPM
C-AXIS (DIRECT CONTROL BY THE BUILT IN MOTOR) (BOTH SPINDLES)
CONTROLLABLE ANGLE: 360° ( 0.001° UNIT)
RAPID FEEDRATE: 200 MIN -1
TURRET (QUICK CHANGE TOOL HOLDER (VDI40) SYNCHRONIZED TAPPING POSSIBLE)
TYPE: V12 V 12
NO. OF TOOLS (ALL LIVE CAPABLE): 12 12 (VDI40)
TOOL SIZE: 1" OD TURING TOOLS
11"/2" ID TURNING TOOLS
M-TOOL (END MILL 0.79" AND TAP M12)
SPINDLE SPEEDS: 100 TO 4500 MIN -1
MAX TOOL SHANK DIAMETER: 0.79"
MOTOR (BUILT IN MOTOR)
SPINDLE DRIVE MOTOR: 20 / 15 HP 20 MIN / CONT
CROSS SLIDE FEED (X-AXIS): XA 5.3 HP
XB 3.3 HP
CARRIAGE FEED (Z-AXIS): 5.3 HP
Y-AXIS: 2.7 HP
C-AXIS: BY SPINDLE DRIVE MOTOR
M-TOOL: 5/3 HP 15 MIN / CONT
MACHINE HEIGHT: 83.27"
NET WEIGHT: 18,700 LBS
For information on a specific piece of equipment, please contact the selling dealer directly.
UED-ed is published by
Used Equipment Directory
400 Morris Ave Ste 268, Denville NJ 07834
Robert Scofield, Publisher. Email: bobs@buyused.com,
Tel: 973-400-1790 Fax: 973-625-8933
|
